need help?
[email protected]
Garage Door Torsion Spring SINGLE RW .250 X 2" ID X Select Length - With Options
$43.29 $72.16
- Product Code: Unbranded
- Availability: 1810
- Price in reward points: 52801
- 1000 Units in Stock
- Condition:New
- Part Type:Springs
- Return shipping will be paid by:Buyer
- MPN:Does Not Apply
- Restocking Fee:20%
- Type:Torsion Spring
- All returns accepted:Returns Accepted
- Brand:Unbranded
- Item must be returned within:30 Days
- Refund will be given as:Money Back
Due limited stock and product availability we will be shipping a limit of 2 pairs (any sizes) of torsion springs per address per day.
One Quality, USA Made* Garage Door Torsion Spring with Replacement Center Bushing and Option to buy Winding Rods
Includes 1 Right Wound Spring, Wire size is .250, Inside Diameter is 2", length is selected in the drop-down list
(Other Lengths are Available, Message Us for Quote)
Please read the complete listing for instructions on how to measure a torsion spring.
From the drop down list you will need to select whether you want a nylon bushing or a steel bearing.
You will receive only ONE (1) bushing or bearing with a pair of springs.
Our springs are made in the USA using Oil Tempered, USA made Wire, -
this makes for a spring that is durable and will outlast imported springs.
Cycle rating depends on the spring size and how many turns are required
,
*Winding and Stationary cones are included and are Pre-installed
(Cones are Imported)
Our springs include a 2 year limited warranty against pre-mature failure
Need help installing or ordering the springs? We provide free support on any products purchased from us.
How to select the correct spring (Please Read)
First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering
Step 1
is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size,
double check by measuring 20 coils and compare to the 10 coil measurement,
if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed..
10-Coil Measurement
20-Coil Measurement
Wire Size
in
cm
in
cm
1 3/4"
4.50
3 1/2"
8.99
0.177
1 7/8"
4.76
3 3/4"
9.53
0.187
1 15/16"
4.88
3 7/8"
9.75
0.192
2"
5.08
4"
10.16
0.200
2 1/16"
5.26
4 1/8"
10.52
0.207
2 3/16"
5.55
4 3/8"
11.11
0.218
2 1/4"
5.72
4 1/2"
11.45
0.225
2 5/16"
5.95
4 5/8"
11.90
0.234
2 7/16"
6.19
4 7/8"
12.38
0.243
2 1/2"
6.35
5"
12.70
0.250
2 5/8"
6.67
5 1/4"
13.34
0.262
2 3/4"
6.93
5 1/2"
13.87
0.273
2 13/16"
7.19
5 5/8"
14.38
0.283
Step 2
is to determine the spring
inside diameter
, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4" and 2" ( Raynor doors use 2 ¼” ID )
Step 3
is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length,
Step 4
is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as
The RW is normally on the Left side and the LW is normally on the Right side
. Be sure to check the wind direction and not make assumptions.
If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction.
We are a Pro Garage Door Installation
and repair Company. We carry many repair parts for many different brands of
doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll
quote a price and set up a listing for you through eBay.
CAUTION
:
Installing or repairing a garage door can be
dangerous task. Garage door springs and cables are under extreme tension and
require appropriate safety precautions. Working with garage doors and
openers could result in personal injury or death. We recommend all installations,
repairs, adjustments, and removals on garage doors be made by a qualified
garage door technician. Any attempts to install, repair, replace, adjust garage
doors or openers are done at your risk. In no event shall
M. C. Overhead Door parts division be liable for damages of any kind,
personal injury or death. User assumes all responsibility/risk for use of
information and products purchased
.
By purchasing
our products you agree to these terms.
RETURN POLICY
Returns are accepted within 30 days of the date that the item is received.
We don't offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased.
Buyer is responsible to pay for the return shipping
If an item is listed with 'free shipping', a 20% restocking fee will be deducted from the refund amount.
All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
One Quality, USA Made* Garage Door Torsion Spring with Replacement Center Bushing and Option to buy Winding Rods
Includes 1 Right Wound Spring, Wire size is .250, Inside Diameter is 2", length is selected in the drop-down list
(Other Lengths are Available, Message Us for Quote)
Please read the complete listing for instructions on how to measure a torsion spring.
From the drop down list you will need to select whether you want a nylon bushing or a steel bearing.
You will receive only ONE (1) bushing or bearing with a pair of springs.
Our springs are made in the USA using Oil Tempered, USA made Wire, -
this makes for a spring that is durable and will outlast imported springs.
Cycle rating depends on the spring size and how many turns are required
,
*Winding and Stationary cones are included and are Pre-installed
(Cones are Imported)
Our springs include a 2 year limited warranty against pre-mature failure
Need help installing or ordering the springs? We provide free support on any products purchased from us.
How to select the correct spring (Please Read)
First of all it is very important to have the correct spring for your door, if the spring is not matched correctly to the door, it will not work properly and can be dangerous or damage your operator. Make sure that you measure the spring correctly and if you have questions, please message us before ordering
Step 1
is to measure the wire diameter. To do this you will need to measure 10 coils then compare that measurement to the chart below to see the wire size,
double check by measuring 20 coils and compare to the 10 coil measurement,
if the 2 measurements do not match, try measuring in a different area of the spring and also make sure the spring is not stretched. Do not measure in the ends where the cones are, the cones stretch the ends where they are installed..
10-Coil Measurement
20-Coil Measurement
Wire Size
in
cm
in
cm
1 3/4"
4.50
3 1/2"
8.99
0.177
1 7/8"
4.76
3 3/4"
9.53
0.187
1 15/16"
4.88
3 7/8"
9.75
0.192
2"
5.08
4"
10.16
0.200
2 1/16"
5.26
4 1/8"
10.52
0.207
2 3/16"
5.55
4 3/8"
11.11
0.218
2 1/4"
5.72
4 1/2"
11.45
0.225
2 5/16"
5.95
4 5/8"
11.90
0.234
2 7/16"
6.19
4 7/8"
12.38
0.243
2 1/2"
6.35
5"
12.70
0.250
2 5/8"
6.67
5 1/4"
13.34
0.262
2 3/4"
6.93
5 1/2"
13.87
0.273
2 13/16"
7.19
5 5/8"
14.38
0.283
Step 2
is to determine the spring
inside diameter
, if the spring is broken you can simply use a ruler to measure the inside of the broken end, if the spring is still in one piece you can measure the outside and deduct the wire size X 2. You also may be able to find stampings on the cones which will help determine the ID, ( P200 or P2000 for 2” and P175 for 1 ¾”) The most common sizes in residential springs are 1 3/4" and 2" ( Raynor doors use 2 ¼” ID )
Step 3
is to measure the length of the spring, Measure the spring only, not including the winding and stationary cone. If the spring is broken measure each piece and add the two measurements together to get the total length. If the spring is still in one piece and wound, it will be longer by 2-3” then when it is relaxed.. the proper way to measure is to unwind the spring to measure the correct length,
Step 4
is only important if ordering a single spring, determine the wind direction of the spring, ( right hand wind ( RW) or left hand wind (LW). Below is an example of the different spring winds. This is probably the most confusing part of the spring ordering process, as
The RW is normally on the Left side and the LW is normally on the Right side
. Be sure to check the wind direction and not make assumptions.
If you look at the end of the spring and compare to the third picture on the listing you will be able to determine the correct wind direction.
We are a Pro Garage Door Installation
and repair Company. We carry many repair parts for many different brands of
doors. If you are looking for a part and we don’t have it listed, just message us through eBay and we’ll
quote a price and set up a listing for you through eBay.
CAUTION
:
Installing or repairing a garage door can be
dangerous task. Garage door springs and cables are under extreme tension and
require appropriate safety precautions. Working with garage doors and
openers could result in personal injury or death. We recommend all installations,
repairs, adjustments, and removals on garage doors be made by a qualified
garage door technician. Any attempts to install, repair, replace, adjust garage
doors or openers are done at your risk. In no event shall
M. C. Overhead Door parts division be liable for damages of any kind,
personal injury or death. User assumes all responsibility/risk for use of
information and products purchased
.
By purchasing
our products you agree to these terms.
RETURN POLICY
Returns are accepted within 30 days of the date that the item is received.
We don't offer exchanges. If a different item is needed, the item not needed can be returned and another item purchased.
Buyer is responsible to pay for the return shipping
If an item is listed with 'free shipping', a 20% restocking fee will be deducted from the refund amount.
All items MUST be returned in the same condition as they were when you received them. If an item is returned damaged or in any way visibly used, an additional deduction will be taken from the refund amount.
